Difference between revisions of "Tcpdump"

From Christoph's Personal Wiki
Jump to: navigation, search
(New page: '''<code>tcpdump</code>''' is a common packet analyzer that runs under the command line. It allows the user to intercept and display TCP/IP and other packets being transmitted or received ...)
 
(Example usage)
Line 54: Line 54:
 
  $ tcpdump -i eth0 arp
 
  $ tcpdump -i eth0 arp
  
* Capture packets flows on a particular port:
+
* Capture packet flows on a particular port:
 
  $ tcpdump -i eth0 port 22
 
  $ tcpdump -i eth0 port 22
  

Revision as of 02:04, 4 January 2014

tcpdump is a common packet analyzer that runs under the command line. It allows the user to intercept and display TCP/IP and other packets being transmitted or received over a network to which the computer is attached.

Example usage

Note: In most of the following examples, I have replaced actual IP addresses with 192.x.x.x (or something similar) and domain names with example.com (or something similar). Otherwise, my example local hostname is "stine" and my example local IPv4 address is "192.168.0.14". Also, some of the output has been removed or modified for illustration purposes.

  • Capture packets from a particular Ethernet interface
$ tcpdump -i eth0
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes
13:40:54.940904 IP stine.local.15342 > example.com.domain: 46527+ PTR? 14.0.168.192.in-addr.arpa. (42)
13:40:54.940918 IP stine.local.15342 > example.com.domain: 46527+ PTR? 14.0.168.192.in-addr.arpa. (42)
13:40:54.963406 IP example.com.domain > stine.local.15342: 46527 NXDomain* 0/1/0 (119)
13:40:54.964613 IP example.com.domain > stine.local.15342: 46527 NXDomain* 0/1/0 (119)
13:40:54.964656 IP stine.local > example.com: ICMP stine.local udp port 15342 unreachable, length 15
...
9 packets captured
32 packets received by filter
0 packets dropped by kernel

Note: When you execute `tcpdump` without any option, it will capture all the packets flowing through all the interfaces. The "-i" option, allows one to filter on a given Ethernet interface.

  • Capture only N number of packets on the eth0 interface:
$ tcpdump -c 2 -i eth0
14:05:49.749471 IP6 fe80::21a:d6ff:fe2b:4641 > ip6-allnodes: ICMP6, router advertisement, length 56
14:05:49.711275 IP stine.local.62198 > example.com.domain: 38572+ PTR? 1.4.6.4.2.6.e....0.8.e.f.ip6.arpa. (90)
  • Display captured packets in ASCII:
$ tcpdump -A -i eth0
  • Display captured packets in HEX and ASCII:
$ tcpdump -XX -i eth0
  • Capture the packets and write output to a binary file (useful for later analysis in, for example, wireshark):
$ tcpdump -w tcpdump-20140103.pcap -i eth0
  • Read the packets from a previously saved file (e.g., from the previous command):
$ tcpdump -tttt -r tcpdump-20140103.pcap
  • Capture packets with their actual IP addresses (instead of the default rDNS lookup):
$ tcpdump -n -i eth0
  • Capture packets with a full timestamp:
$ tcpdump -tttt -n -i eth0
2014-01-03 14:19:16.882379 IP6 fe80::21a:d6ff:fe2b:4641 > ff02::1: ICMP6, router advertisement, length 56
2014-01-03 14:19:19.882169 IP6 fe80::21a:d6ff:fe2b:4641 > ff02::1: ICMP6, router advertisement, length 56
  • Capture packets with greater than N bytes:
$ tcpdump -i eth0 greater 1024
  • Capture packets with less than N bytes:
$ tcpdump -i eth0 less 1024
  • Capture only the packets of a specific protocol type (e.g., ip, ip6, arp, rarp, decnet, tcp, udp, fddi, tr, wlan, etc.):
$ tcpdump -i eth0 arp
  • Capture packet flows on a particular port:
$ tcpdump -i eth0 port 22
  • Capture packets for particular destination IP and port
$ tcpdump -i eth0 dst 192.x.x.x and port 22
  • Capture all packets, but filter out given protocals (e.g, "arp" and "rarp"):
$ tcpdump -i eth0 not arp and not rarp

Note: You can pass combinations of "and", "or", and "not" conditions.

Examples derived from the tcpdump man page

  • Print all packets arriving at or departing from sundown:
$ tcpdump host sundown
  • Print traffic between helios and either hot or ace:
$ tcpdump host helios and \( hot or ace \)
  • Print all IP packets between ace and any host except helios:
$ tcpdump ip host ace and not helios
  • Print all traffic between local hosts and hosts at Berkeley:
$ tcpdump net ucb-ether
  • Print all FTP traffic through Internet gateway snup (note that the expression is quoted to prevent the shell from (mis-)interpreting the parentheses):
$ tcpdump 'gateway snup and (port ftp or ftp-data)'
  • Print traffic neither sourced from nor destined for local hosts (if you gateway to one other net, this stuff should never make it onto your local net):
$ tcpdump ip and not net localnet
  • Print the start and end packets (the SYN and FIN packets) of each TCP conversation that involves a non-local host:
$ tcpdump 'tcp[tcpflags] & (tcp-syn|tcp-fin) != 0 and not src and dst net localnet'
  • Print all IPv4 HTTP packets to and from port 80 (i.e., print only packets that contain data, not, for example, SYN and FIN packets and ACK-only packets; IPv6 is left as an exercise for the reader):
$ tcpdump 'tcp port 80 and (((ip[2:2] - ((ip[0]&0xf)<<2)) - ((tcp[12]&0xf0)>>2)) != 0)'
  • Print IP packets longer than 576 bytes sent through gateway snup:
$ tcpdump 'gateway snup and ip[2:2] > 576'
  • Print IP broadcast or multicast packets that were not sent via Ethernet broadcast or multicast:
$ tcpdump 'ether[0] & 1 = 0 and ip[16] >= 224'
  • Print all ICMP packets that are not echo requests/replies (i.e., not `ping` packets):
$ tcpdump 'icmp[icmptype] != icmp-echo and icmp[icmptype] != icmp-echoreply'

See also

External links